!
!
!

Dreesens

Set includes 2 x down tube (295 mm x 32 mm), 2 x seat tube (265 mm x 28 mm) 1 x headbadge (45 mm x 36 mm). Available in various colours and now including matt black. This set is for a carbon or alloy frame, but can be reduced for older steel frames. See also headbadges for printed version of head badge.

Eriksen

Set includes 2 x down tube (295 mm x 35 mm), 2 x seat tube (184 mm x 27 mm) 1 x headbadge (55 mm x 55 mm). Available in various colours and now including matt black. I produced this set for a well known Yorkshire frame builder, for a tandem frame, although this set could be used for a carbon or alloy frame and can be reduced in size for older steel frames.

Eriksen V2

Set includes 2 x down tube (231 mm x 30 mm), 2 x seat tube (208 mm x 27 mm). Available in various colours and now including matt black.

Felt

Set includes 2 x down tube (280 mm x 42 mm), 2 x seat tube/top tube (150 mm x 22 mm),  1 x headbadge (51 mm x 51 mm)  2 x small (36 mm x 36 mm).

Jamis quest

Circa 2003 Jamis quest, not sure if this should be in classic or modern, so I've shown it in both! Digitally re-created and printed onto top quality vinyl. Set includes 2 x down tube (245 x 20 mm), 2 x top tube (147 x 16 mm), 1 x tubing decal (853). Seen here on a silver background (not included) Other colours may be available. info@wanit.co.uk

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Land Shark

Not sure if this should be in modern or classic,so I have listed in both! Set includes 2 x down tube (223 x 28 mm), 2 x seat tube (223 x 28 mm), 1 x head/seat (42 x 42 mm), Optional tubing decal

Lemond Tete De Course (Titanium/carbon)

Digitally re-mastered and produced in quality 70 micron vinyl, a must for all Lemond fans. Not sure if this should be in classic or modern, so I've listed in both! One of the latest from Greg Lemond, built in a mixture of Reynolds Titanium and Carbon. The models that I have seen have the lettering in white with blue panels picked out with white/black stripes at the ends. As these frames have bottle cage eyes, it is not possible to include the printed blue panels as it is not possible to wrap these over the eyes (some say it is but I disagree), so these as with the originals would have to be painted on.To complete the set I have included a printed head badge, although the originals did have a moulded metal or plastic one.

It may be possible to produce these in other colours, but all samples I have seen have been in this colourway.

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Lemond Tete De Course (Titanium/carbon)V2

Digitally re-mastered and produced in quality 70 micron vinyl, a must for all Lemond fans. Not sure if this should be in classic or modern, so I've listed in both! One of the latest from Greg Lemond, built in a mixture of Reynolds Titanium and Carbon. This model has the lettering in black with silver outlines picked out with white/black stripes at the ends. As these frames have bottle cage eyes, it is not possible to include the printed blue panels as it is not possible to wrap these over the eyes (some say it is but I disagree), so these as with the originals would have to be painted on.To complete the set I have included a printed head badge, although the originals did have a moulded metal or plastic one.

It may be possible to produce these in other colours, but all samples I have seen have been in this colourway.

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Lemond Tete De Course (Titanium/carbon)V3

Digitally re-mastered and produced in quality 70 micron vinyl, a must for all Lemond fans. Not sure if this should be in classic or modern, so I've listed in both! One of the latest from Greg Lemond, built in a mixture of Reynolds Titanium and Carbon. This model has the lettering in black with white/black stripes at the ends (these can also be in black/red as one model I have seen).The Tete De Course is in white. As these frames have bottle cage eyes, it is not possible to include the printed blue panels as it is not possible to wrap these over the eyes (some say it is but I disagree), so these as with the originals would have to be painted on.To complete the set I have included a printed head badge, although the originals did have a moulded metal or plastic one.

It may be possible to produce these in other colours, but all samples I have seen have been in this colourway. info@wanit.co.uk 

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Lemond Versailles Carbon

Set includes 2 x down tube (188 mm x 30 mm), 2 x seat tube (151 mm x 24 mm), 2 x forks (130 mm x 21 mm), 2 x top tube (98 x 10 mm), 2 x Bontrager Race fork decals (92 x 19 mm). The original head badge was of the pressed metal/moulded plastic variety, which I cannot offer but if this item is lost/damaged, I offer a monochrome printed version as pictured.

Seen here in white on a black background (not included)

Lynskey

Set includes 2 x down tube (253 mm x 33 mm), 2 x seat tube/top tube (185 mm x 24 mm),  1 x printed headbadge 40 mm x 49 mm) 

Merlin Works 4.0

Set includes 2 x down tube (350 mm x 33 mm), 2 x seat tube (175 mm x 17 mm), 2 x top tube (200 mm x 20 mm).

Quintana Roo

Set includes 2 x down tube (297 mm x 30 mm), 2 x seat tube (206 mm x 21 mm) 1 x headbadge (62 mm x 30 mm), 2 x forks (38 x 18 mm). Available in various colours and now including matt black, mirror gold and silver

Richard Sachs

Set includes 2 x Down tube (250 x 29 mm), 2 x forks (120 x 10 mm), 1 x head (50 x 49 mm), 1 x combined seat pattern (270 x 85 mm).,

Ritchey

This version was taken from an oversized steel frame, but would be suitable for standard, alloy or carbon. Set includes 2 x down tube (197 mm x 30 mm), 2 x Seat Tube (197 mm x 30 mm), 1 x head badge (37 x 54 mm).

I offer this version with a tubing decal if required. Other tubing decals may be available info@wanit.co.uk

Rock Lobster

Suitable for alloy or carbon frames. For steel version please see classic decals
Set includes 2 x down tube (257 mm x 33 mm), 2 x seat tube (206 mm x 24 mm).

SantaCruz V3

Set includes 2 x down tube (350 mm x 35 mm), 2 x seat tube (220 mm x 22 mm), 2 small man for down tube (45 x 35 mm), 1 x head (58 x 46 mm). This set is contour cut with no background, thus the colour of the farme will be the background.

Schwinn Peloton

Set includes 2 x Down tube (250 x 23 mm), 2 x top tube  (84 x 12 mm), 1 x head, 1 x seat (51 x 51 mm). Relevant tubing decal also available as option. Available in various colours, although head/seat badge will always be as shown.

Serotta (Digital)

Digitally printed

Digitally printed in various colours. Set includes 2 x down tube (228 x 31 mm), 2 x seat tube (187 x 37 mm), 1 x head (40 x 62 mm), 2 x top tube (123 x 17 mm), 1 x made in USA shield, choice of tubing decal, choice of frame type (in solid lettering, same colour as outline of main decals). This set is white with choice of colour as outline. Can be produced in variety of other colours. info@wanit.co.uk

 

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals

Specialized FSR

Set includes 2 x down tube (290 mm x 35 mm), 2 x FSR (120 mm x 20 mm), 1 x head badge (42 x 95 mm)

S-WORKS

Set includes 2 x down tube (300 mm x 32 mm), 2 x seat tube (150 mm x 18 mm), 2 x pistol-mirrored (50 mm x 52 mm),  1 x headbadge (30 mm x 60 mm), 2 x chainstay-mirrored (170 mm x 17 mm)

Trek OCLV

Set includes 2 x down tube (250 mm x 36 mm), 2 x seat tube (175 mm x 25 mm), 1 x headbadge (50 mm x 33 mm), 2 x OCLV (62 mm x 11 mm).

Trek Speed Concept

Set includes 2 x down tube (410 mm x 41 mm), 2 x forks (180 mm x 21 mm), 2 x seat stays (180 x 21 mm), 1 x headbadge (67 mm x 81 mm)

Trek 850 digital

Digitally re-mastered classic Trek United 850. Printed using the very latest state of the art technology. Set is as shown including down tube, seat tube, top tube, head badge and upper seat tube, 2 x seat tube  Shown here in black with a silver outline.

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Yamaguchi V1

Set includes 2 x down tube (225 x 25 mm), 2 x seat tube (197 x 27 mm), 1 x head/seat (50 x 58 mm), 2 x top tube 'stars' (34 x 34 mm). This set is for an older steel frame with tubing of 28.6 mm (Columbus, Reynolds etc). The sizes can be scaled to suit modern frames with larger tubing info@wanit.co.uk

YETI

Set includes 2 x down tube (295 mm x 37 mm), 2 x seat tube (206 mm x 28 mm) 1 x headbadge (49 mm x 69 mm). Available in various colours and now including matt black, mirror gold and silver

YETI V2 Keyline

Set includes 2 x down tube (295 mm x 37 mm), 2 x seat tube (206 mm x 28 mm) 1 x headbadge (49 mm x 69 mm). Available in various colours and now including matt black. This is a 'keyline' version so the background would be the colour of the frame which will show through